GJS-H004 Horizontal Fiber Optic Splice Closure

Weight (excluding outside box)

2750g-3200g

Number of inlet/outlet ports

3 (pieces) on each side (total 6 pieces)

Diameter of fiber cable

Φ8-Φ23 (mm)

Capacity of FOSC

Bunchy: 6-96 (Cores)
     Ribbon: max. 216 (Cores)

1

Housing(bottom)

1 set

Protecting fiber cable splices in the whole

Internal diameter:
     378*136 (mm)

2

Housing(cover)

1 set

Protecting fiber cable splices in the whole

Internal diameter:
     378*136 (mm)

3

Insert plate

2 pairs

Fixing the housing

175x56x30(mm)

4

Fiber optic splice tray
     (FOST)

Max.4 trays (bunchy) or Max.4 trays (ribbon)

Fixing the shrinkable protective sleeve and holding fibers

Suitable for: Bunchy: 6,8,12,16,24(cores) Ribbon: 3 (pieces)

5

Foundation

1 set

Fixing fiber cable, reinforced core, and FOST

6

Seal fitting

1 set

Sealing between the FOSC cover and the FOSC bottom

7

port plug

6 pieces

Sealing empty ports

8

Fixed bolt

1 sets

Fixing the house

2

Nylon tie

Fixing fiber with a protective coat

Configuration as per capacity

3

Insulation tape

1 roll

Enlarging the diameter of the fiber  cable for easy fixing

4

Seal tape

1 roll

Enlarging the diameter of the fiber  cable, which fits in with the seal fitting

Configuration as per specification

5

Hanging hook

1 set

For aerial use

6

Earthing wire

1 piece

Putting through between the earthing devices

To put through as per the actual requirement

7

Abrasive cloth

1 piece

Scratching the fiber cable

8

Labeling paper

1 piece

Labeling fiber

M8 Special wrench

1 pieces

Fixing the bolts of the housing and inserting the plate

9

M6 Special wrench

1 pieces

Fixing small bolts of housing

10

M10 Special wrench

1 piece

Tightening the nut of the reinforced core

11

Measuring paper

1 piece

To measure the circle, whose diameter is enlarged with seal tape

12

Instruction manual

1 piece

Standard installation

1

inner box

45.8*21.5*12

1pcs

2.85-3.3kg

Configuration as per weight

2

outer box

63.5*46.5*47

10pcs

28.5-33kg

Configuration as per weight

Inspecting item

Technical Requirements

Inspecting type

Routine test (Before leaving the factory)

Type test

Package

Each small package contains one fiber optic splice closure, together with its accessories, tools, installation manual, and packing list.

full

At least 3 sets sampled each time

Appearance

Intact in shape, no burrs, bubbles, chaps, pores, warps, impurities and other defects, all background colors should be even and continual.

Sign

There is a clear sign on the housing, such as the name and model of the product etc.

Fiber storage device

The fibers reserved are to be wound in a fiber optic splice tray (FOST); the length of fibers housed in FOST is >1.6m, and the curved radius is >30mm. During the installation and maintenance, there should be no attenuation on fibers.

At least 3 sets sampled each time

Electrical jointing device

Inside FOSC, metallic components of fiber cables have the functions of electrical transmission, earthing connection, and disconnecting. It is possible to install an earthing deriving device outside the housing

Sealing performance

After sealing according to the stipulated operation procedures, the injected air pressure is 100KPa±5Kpa. When immersed in clean water of normal temperature for 15 minutes, there should be no air bubbles, then observed for 24 hours, there should be no change in air pressure.

Re-sealing performance

After reopening and resealing according to the stipulated operation procedures, the injected air pressure is 100KPa±5Kpa. When immersed in clean water of normal temperature for 15 minutes, there should be no air bubbles, then observed for 24 hours, there should be no change in air pressure.

Pull

Bearing pull is ≧ 800N at axle orientation; there should be no breakage on the housing.

Punching

Bearing pressure of 2000N/10cm for 1 minute, there should be no breakage on the housing

Impact

Bearing impact energy of 16N•m, 3 times of impacts, there should be no breakage on the housing

Bending

The spot between the FOSC and seal fitting can bear bending tension of 150N at a bending angle of ±45⁰ for 10 circles, and there should be no breakage on the housing

Torsion

Bearing torsion 50N•m, 10 circle at torsion angle±90^0,

There should be no breakage on the housing.

Temperature circle

Injected air pressure of 60KPa±5 KPa, the temperature circle ranging from -40℃~+65℃, 10 times of the circular tests (one circular consists of high temperature for 2 hours + indoor temperature for 2 hours + low temperature for 2 hours + indoor temperature for 2 hours ) when the pressure declines, the amplitude is ≦5Kpa, immerse the swatch in clean water of normal temperature for 15 minutes, there should be no air bubbles.

Voltage resistance strength

After sealing the FOSC according to the stipulated operation procedures, immerse it in clean water of normal temperature in 1.5m for 24 hours. There should be no breakdown or arc over between the metallic components of the FOSC, between metallic components and the ground at DC 15 kV for 1 minute.

Isolating resistance

After sealing the FOSC according to the stipulated operation procedure, immerse it in clean water at 1.5m for 24h; the isolating resistance between the metallic components of the FOSC, between the metallic components and the ground should be ≧ 2×10⁴MΩ.